[. . . ] Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2010
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] Do not unplug the power cord until the POWER LED stops flashingindicating the projector has cooled down.
11
DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 17 and Setting the OSD Language on page 18 for help on using OSD menus. )
Important: Keep the password in a safe place. If you lose the password, contact your reseller for information on clearing the password.
1. 2.
Press the MENU button to open the OSD menu.
Press the cursor button to move to the Installation I menu.
3. 4.
Press the cursor button to select Advanced.
Press
(Enter) / .
12
DLP Projjecttor User''s Manuall DLP Pro ec or User s Manua
5. 6.
Press the cursor button to select Security Lock.
Press the cursor button to enable or disable security lock function. A password dialog box automatically appears.
7.
You can use the cursor buttons either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Push the MENU button to exit the dialog box.
8.
The password confirm menu appears when user presses the power-on key in case the Security Lock is enabled. Service center will validate the owner and help reset the password.
13
DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua
Adjusting the Projector Level
Take note of the following when setting up the projector:
The projector table or stand should be level and sturdy. You could trip over them.
1.
To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B]. 3.
To lower the level of the projector, press the height-adjuster button and push down on the top of the projector.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the desired angle has been achieved.
14
DLP Projjecttor User''s Manuall DLP Pro ec or User s Manua
Adjusting the Zoom, Focus and Keystone
1.
Use the Image-zoom control (on the projector only) to resize the projected image and screen size B .
2.
Use the Image-focus control (on the projector only) to sharpen the projected image A .
3.
Press the Keystone buttons on the remote control or press KEYSTONE and use or on the keypad to correct image-trapezoid (wider top or bottom) effect.
Remote control and OSD panel
4.
The keystone control appears on the display.
15
DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua
Adjusting the Volume
1.
Press the Volume +/buttons on the remote control or press VOLUME and use or on the keypad to adjust volume.
Remote control and OSD panel
2. Press the MUTE button to turn off the volume (This feature is available only on the remote).
16
DLP Projjecttor User''s Manuall DLP Pro ec or User s Manua
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector.
1. Press MENU to close the OSD or leave a submenu.
Note: Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC. Items that are not available cannot be accessed and are grayed out.
17
DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button twice to close the OSD.
18
DLP Projjecttor User''s Manuall DLP Pro ec or User s Manua
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
19
DLP Projjecttor--User''s Manuall DLP Pro ec or--User s Manua
OSD Sub-Menu Overview
Image / Advanced Video / Audio / Audio
Color Space
Auto, RGB, YCbCr, YPbPr
Volume
0~8
Color Temperature
Normal, Cold, Warm
Mute
On, Off
Color Manager
Installation I / Advanced
Image / Advanced / Color Manager
Security Lock
On, Off
Hue
0 ~ 100
Keypad Lock
On, Off
Red
Saturation
0 ~ 100
Wall Color
Off, Light Yellow, Pink, Light Green, Blue, Blackboard
Gain
0 ~ 100
Presentation Timer Installation I / Advanced / Presentation Timer Timer Alarm Off~ 60mins
Hue
0 ~ 100
Green
Saturation
0 ~ 100
Gain
0 ~ 100
Time Keeper
Off~ 60mins
Hue
0 ~ 100
Start Counting
Blue
Saturation
0 ~ 100
Installation II / Advanced
Installation II / Advanced / OSD Menu Setting
Gain
0 ~ 100
OSD Menu Setting
Menu Position
Center, Down, Up, Left, Right
Hue
0 ~ 100
Peripheral Test
Translucent Menu
0%, 25%, 50%, 75%, 100%
Cyan
Saturation
0 ~ 100
Lamp Hour Reset
Menu Display On, Off On, Off
10 ~ 20
Gain
0 ~ 100
Low Power Mode 3D
Hue
0 ~ 100
Magenta
Saturation
0 ~ 100
3D Inverter
R/L, L/R
Gain
0 ~ 100 Installation II / Advanced / Peripheral Test
Hue
0 ~ 100
Installation II / Status
Yellow
Saturation
0 ~ 100 Active Source Remote Control Test
Gain
0 ~ 100 Video information Color Test
Red
0 ~ 100 Lamp Hours(Eco , Normal) Button Test
White
Green
0 ~ 100
Blue
0 ~ 100
20
DLP Projjecttor User''s Manuall DLP Pro ec or User s Manua
Image Menu
Press the MENU button to open the OSD menu. Press to change values for settings.
ITEM
Display Mode Brilliant Color Brightness Contrast Sharpness Gamma Advanced Reset
DESCRIPTION
Press the cursor button to set the Didplay Mode. Note: Regarding Display Mode, the parameter adjustments are disabled except for User mode. Press the cursor button to adjust the gamma correction of the display. [. . . ] If you have replaced the lamp recently, try resetting the lamp connections. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. [. . . ]